GHW-3 L’opérateur de porte électrique à vis sans fin à arbre intermédiaire GHW-3 est idéal pour les endroits où l’atmosphère contient de la poussière, de l’huile, de l’eau ou des vapeurs liquides. Conçu sur mesure principalement pour les grandes portes à rideaux roulants, les portes à levage vertical, les portes empilables et les petites portes de hangar coulissantes
Réduction:
Réducteur à vis sans fin, à un étage, fonctionnant dans un bain d’huile, rapport 40:1, conception à bride en C, boîtier en alliage de fonte. Chaîne à rouleaux n° 60 et pignons de l’arbre de l’opérateur à l’arbre de la porte. Vitesse de la porte : 7″ (18cm) par seconde env.
Limiteur de couple réglable :
Protégera la porte et l’opérateur en cas d’obstruction (en option moyennant des frais supplémentaires).
Interrupteurs de fin de course :
Type rotatif avec cames en bronze oilite et micro-interrupteurs de précision pour l’arrêt automatique de la porte en position ouverte ou fermée (facilement réglable sans outils).
Contacteur inverseur :
Type à usage intensif.
Commande à trois boutons :
Type de contact momentané pour ouverture, fermeture, arrêt. L’opérateur peut être arrêté dans n’importe quelle position et la porte ouverte ou fermée à partir de cette position. Le bouton de fermeture peut être câblé pour une pression constante lorsque cela est spécifié. Circuit de commande : 24V. A.C. pour la protection de l’utilisateur, Classe II.
Palan à chaîne:
Équipé d’un dispositif de déconnexion qui permet à une personne de désengager l’opérateur de la porte et d’actionner le palan à chaîne depuis le sol, à la main, en cas de panne de courant, sans avoir à retirer la chaîne à rouleaux d’entraînement. Les interrupteurs de fin de course ne se dérégleront pas lorsque le palan est utilisé.
Verrouillage de sécurité :
L’interrupteur de verrouillage électrique coupe automatiquement l’alimentation de la commande de l’opérateur lorsque le palan à chaîne est en marche.
Montage:
Gauche et droite (doit être spécifié). Main droite illustrée.
Relais de surcharge manuel :
Pour la protection contre les surintensités et les sous-tensions (réarmement manuel).
Moteur:
3 CV (2239W) 208V., 230V., 416V., 460V., 550V. Triphasé (monophasé non disponible).
Espace latéral requis :
24″ (61cm) minimum.
Finir:
Apprêté avec un apprêt antirouille et peint par pulvérisation en émail bleu martelé.
Three Button Control:
Momentary contact type for open, close, stop. Fully guarded, weatherproof, 250V. A.C. maximum. Screw type terminal.
Motor Control:
Heavy duty reversing contactor, two sets of three pole contactors on a common frame, mechanically interlocked to prevent simultaneous closure, clapper-type armature with three point suspension, auxiliary contacts SPDT or DPDT (as required) on each armature. Holding coils 24V. A.C. Contact rating: resistive: 15 amps @ 120V. A.C., 10 amps @ 240V. A.C., 5 amps @ 600 V. A.C.; inductive: 2 H.P. (1493W) max. Terminals: .25″ (.63cm) quick connect. Mechanical life: over 10 million cycles.
Reduction:
Worm gear reducer, single stage, running in an oil bath with 40:1 ratio, C flange design, alloy cast iron housing. Hardened and ground steel worm and bronze alloy gear for greater wear life. High speed taper roller bearings, double lip, spring loaded seals to keep lubricant in and dirt out. Alloy steel shaft, hardened and ground for greater strength. Input 1750 RPM. 3 H.P. (2239W). Output torque: 2490in/lbs (2161cm kg). Overhang load: 1400 lbs. (636kg). Output shaft diameter: 1-3/8″ (3.5cm), speed 44 RPM. Door speed 7″ (18cm) per second approx.
Unit Chassis:
1/4″ (0.63cm). Heavy steel channel frame assembly reinforced with steel gusset plates, bolted together for greater strength.
Limit Switches:
Rotary type, friction free, oilite bronze cams, grooved and lock guided in a spring loaded, formed galvanised steel plate. Cams are fitted on 5/8″ x 10-3/4″ (1.59cm x 26.88cm) C.R. steel shaft, rotating on lubricated high speed ball bearings. Cams on their preset travel, activate the micro switches to cut power of motor control in both open and close directions. Operating force on limit switch: 4 oz. (113.4g) maximum. Contact separation: .020″ (.05cm). Terminations .25″ (.63cm) quick connect.
Manual Overload Relay:
Protects operator from overcurrent and under voltage. Manual reset.
Electrical Control Cabinet:
Factory pre-wired, made of sheet metal; construction of suitable rigidity designed to meet EEMAC and C.S.A. classification type 12 and type 4. Size: 8″ x 16″ x 5″ (20cm x 41cm x 13cm) with removable cover for easy servicing and maintenance. Mounted to unit chassis with four zinc plated steel bolts.
50 V.A. Step-Down Transformer:
208V., 230V., 416V., 460V., 600V. A.C. primary to 24V. A.C. secondary, Class II.
Emergency Chain Hoist:
Combined with a floor operated disconnect which, when pulled, will disconnect the electrically driven solenoid brake and engage the chain hoist for manual operation, in the event of power failure, without having to remove the main drive chain. Assembly consists of a grooved aluminium pocket wheel, lever arm, coupling, 1/8″ (.31cm) D. pull cable, 7/16″ (11.1mm) D. bright polish chain, wall chain keeper and disconnect arm.
Safety Electrical Interlock:
When chain hoist is in operation, a toggle switch cuts the power line of operator control automatically. This safety electrical interlock will protect operator and door when power is restored and push button station is pressed accidentally.
Adjustable Torque Limiter (Optional at extra cost):
This patent-pending torque limiter consists of a steel hub with two 4″ diam. clutch plates, a 60B23 sprocket, two 4″ diam. non-flammable friction fibre discs, and a spring washer with pressure cup. Holding force is from 50 to 1500 lbs. (23 to 680kgs). Can be adjusted in the field as required, depending on door weight. Torque limiter will protect door and operator in case of obstruction or if door gets jammed. Synchronized limit drive assembly will not go out of adjustment when torque limiter is activated.
Motor:
T.E.F.C. rated for continuous duty 3 H.P. (2239W). Voltages available: 208V., 230V., 416V., 460V. or 550V., three phase, 1725 RPM. Ball bearings permanently lubricated. Frame: 143TC, 145TC. Shaft diameter: 7/8″ (2.22cm). (Single phase not available).
Maximum door area: 1600 sq. feet (149m2).
Maximum lifting capacity: 6800 lbs. (3084kg).
Unit is factory pre-wired, colour coded and tagged.
Wiring diagrams are enclosed with each operator.
Operator is pre-run and tested before shipment.
Chef de file en opérateurs de
portes et de barrières