Residential
Electric Door and Gate Operators

Commercial-Industrial
Trolley type-ceilling, Wall Mounts, B1-Parting, Sliding Doors Electric Operators

Waterproof
Trolley Type-Ceillling and Jack-Shaft-Wall Mount

Explosion-proof
Trolley Type-Ceillling and Jack-Shaft-Wall Mount

Sliding Gate
Electric Operators

Swing Gate
Electric Operators

Trafic control barriers
To control of vehicular traffic in private and public parking areas.

Rolling &Fire Doors
Rolling Service Doors & Fire Doors. Jack Shaft - Wall Mount

Accessories
Different accessories for your needs

Safety Devices
Reverse Systems and Sensor

Entry-Exit Devices
Loop Detectors, Card Reader and more

Operating Controls
 

Modifications
 

Special applications
 
 

GENERAL INFORMATION

GHW-3 jackshaft worm-gear electric door operator is ideally suited for locations where atmosphere contains dust, oil, water or liquid vapours. Custom designed mainly for large rolling curtain doors, vertical-lift doors, stacking type doors and small sliding hangar doors

Reduction:
Worm gear reducer, single stage, running in an oil bath, 40:1 ratio, C flange design, cast iron alloy housing. No. 60 roller chain and sprockets from operator shaft to door shaft. Door speed: 7" (18cm) per second approx.

Adjustable Torque Limiter:
Will protect door and operator in case of obstruction (optional at extra cost).

Limit Switches:
Rotary type with oilite bronze cams and precision micro switches for automatic stopping of door in open or closed positions (easily adjustable without tools).

Reversing Contactor:
Heavy duty type.

Three Button Control:
Momentary contact type for open, close, stop. Operator may be stopped in any position and door opened or closed from that position. Close button can be wired for constant pressure when specified. Control circuit: 24V. A.C. for user's protection, Class II.

Chain Hoist:
Equipped with a disconnect device which allows a person to disengage the operator from the door and operate the chain hoist from the floor, by hand, in the event of power failure, without having to remove the drive roller chain. Limit switches will not go out of adjustment when hoist is used.

Safety Interlock:
Electrical interlock switch automatically cuts power of operator control when chain hoist is in operation.

Mounting:
Left and right (must be specified). Right hand shown.

Manual Overload Relay:
For overcurrent and under voltage protection (manual reset).

Motor:
3 H.P. (2239W) 208V., 230V., 416V., 460V., 550V. Three phase (single phase not available).

Sideroom Required:
24" (61cm) minimum.

Finish:
Primed with rust-proof primer and spray painted in blue hammertone enamel.



SPECIFICATIONS


Three Button Control:
Momentary contact type for open, close, stop. Fully guarded, weatherproof, 250V. A.C. maximum. Screw type terminal.

Motor Control:
Heavy duty reversing contactor, two sets of three pole contactors on a common frame, mechanically interlocked to prevent simultaneous closure, clapper-type armature with three point suspension, auxiliary contacts SPDT or DPDT (as required) on each armature. Holding coils 24V. A.C. Contact rating: resistive: 15 amps @ 120V. A.C., 10 amps @ 240V. A.C., 5 amps @ 600 V. A.C.; inductive: 2 H.P. (1493W) max. Terminals: .25" (.63cm) quick connect. Mechanical life: over 10 million cycles.

Reduction:
Worm gear reducer, single stage, running in an oil bath with 40:1 ratio, C flange design, alloy cast iron housing. Hardened and ground steel worm and bronze alloy gear for greater wear life. High speed taper roller bearings, double lip, spring loaded seals to keep lubricant in and dirt out. Alloy steel shaft, hardened and ground for greater strength. Input 1750 RPM. 3 H.P. (2239W). Output torque: 2490in/lbs (2161cm kg). Overhang load: 1400 lbs. (636kg). Output shaft diameter: 1-3/8" (3.5cm), speed 44 RPM. Door speed 7" (18cm) per second approx.

Unit Chassis:
1/4" (0.63cm). Heavy steel channel frame assembly reinforced with steel gusset plates, bolted together for greater strength.

Limit Switches:
Rotary type, friction free, oilite bronze cams, grooved and lock guided in a spring loaded, formed galvanised steel plate. Cams are fitted on 5/8" x 10-3/4" (1.59cm x 26.88cm) C.R. steel shaft, rotating on lubricated high speed ball bearings. Cams on their preset travel, activate the micro switches to cut power of motor control in both open and close directions. Operating force on limit switch: 4 oz. (113.4g) maximum. Contact separation: .020" (.05cm). Terminations .25" (.63cm) quick connect.

Manual Overload Relay:
Protects operator from overcurrent and under voltage. Manual reset.

Electrical Control Cabinet:
Factory pre-wired, made of sheet metal; construction of suitable rigidity designed to meet EEMAC and C.S.A. classification type 12 and type 4. Size: 8" x 16" x 5" (20cm x 41cm x 13cm) with removable cover for easy servicing and maintenance. Mounted to unit chassis with four zinc plated steel bolts.

50 V.A. Step-Down Transformer:
208V., 230V., 416V., 460V., 600V. A.C. primary to 24V. A.C. secondary, Class II.

Emergency Chain Hoist:
Combined with a floor operated disconnect which, when pulled, will disconnect the electrically driven solenoid brake and engage the chain hoist for manual operation, in the event of power failure, without having to remove the main drive chain. Assembly consists of a grooved aluminium pocket wheel, lever arm, coupling, 1/8" (.31cm) D. pull cable, 7/16" (11.1mm) D. bright polish chain, wall chain keeper and disconnect arm.

Safety Electrical Interlock:
When chain hoist is in operation, a toggle switch cuts the power line of operator control automatically. This safety electrical interlock will protect operator and door when power is restored and push button station is pressed accidentally.

Adjustable Torque Limiter (Optional at extra cost):
This patent-pending torque limiter consists of a steel hub with two 4" diam. clutch plates, a 60B23 sprocket, two 4" diam. non-flammable friction fibre discs, and a spring washer with pressure cup. Holding force is from 50 to 1500 lbs. (23 to 680kgs). Can be adjusted in the field as required, depending on door weight. Torque limiter will protect door and operator in case of obstruction or if door gets jammed. Synchronized limit drive assembly will not go out of adjustment when torque limiter is activated.

Motor:
T.E.F.C. rated for continuous duty 3 H.P. (2239W). Voltages available: 208V., 230V., 416V., 460V. or 550V., three phase, 1725 RPM. Ball bearings permanently lubricated. Frame: 143TC, 145TC. Shaft diameter: 7/8" (2.22cm). (Single phase not available).

Maximum door area: 1600 sq. feet (149m2).
Maximum lifting capacity: 6800 lbs. (3084kg).

Unit is factory pre-wired, colour coded and tagged.
Wiring diagrams are enclosed with each operator.
Operator is pre-run and tested before shipment.